Updated CAD, STL's

Mods/hbo/ServoKlicky/Firmware/Printer.cfg

@@ -0,0 +1,139 @@
+# This file contains only the sections related to the probe configuratioo
+# THIS IS NOT A CEMPLETE KLIPPER PRINTER CONFIGURATION
+#
+# You need to adjust some values to your printer and probe mounting dimensions
+# This paricular config ia based on my tri-zero usinge the Ghost-LG toolhead and a euklid probe
+# that docks into the servo-klicky 
+# 
+# The pin configuration is for a SKR Pico board.
+# Note: You need to add a jumper on the pico to enablke the servo pins (see PICO manual for details) 
+
+
+[include euklid.cfg]
+
+
+#####################################################################
+#      Additiponal Components 
+#####################################################################
+
+
+#################################
+#      Probing 
+#################################
+
+[servo probe_servo]
+pin: gpio29
+#   PWM output pin controlling the servo. This parameter must be
+#   provided.
+maximum_servo_angle: 140
+#   The maximum angle (in degrees) that this servo can be set to. The
+#   default is 180 degrees.
+minimum_pulse_width: 0.0008
+#   The minimum pulse width time (in seconds). This should correspond
+#   with an angle of 0 degrees. The default is 0.001 seconds.
+maximum_pulse_width: 0.0022
+#   The maximum pulse width time (in seconds). This should correspond
+#   with an angle of maximum_servo_angle. The default is 0.002
+#   seconds.
+initial_angle: 115
+#   Initial angle (in degrees) to set the servo to. The default is to
+#   not send any signal at startup.
+#initial_pulse_width:
+#   Initial pulse width time (in seconds) to set the servo to. (This
+#   is only valid if initial_angle is not set.) The default is to not
+#   send any signal at startup.
+
+
+[probe]
+pin: EBBCan: PB8        # Adjust to your board
+x_offset: -23           # Adjust to your probe mount
+y_offset: -10.0         # Adjust to your probe mount
+
+#z_offset: 7.05  # this value is from the probe result using feeler gauge to set Z height 
+#   The distance (in mm) between the bed and the nozzle when the probe
+#   triggers. This parameter must be provided.
+speed: 5
+samples: 2
+samples_result: average
+sample_retract_dist: 5.0
+samples_tolerance: 0.005
+samples_tolerance_retries: 3
+lift_speed: 30
+
+
+
+#####################################################################
+# Homing and Gantry Adjustment Routines
+#####################################################################
+
+
+
+[homing_override]
+axes: z
+gcode:
+    {% set euclid_probe = printer["gcode_macro EuclidProbe"] %}
+
+    QUERY_PROBE
+    _ASSERT_PROBE_STATE MUST_BE=stowed
+
+    # ensure the servo dock is in park position !!
+    # homing z with the dock exposed might kill the servo gears !!
+    SET_SERVO SERVO=probe_servo ANGLE=115
+
+    G28 X
+    G28 Y
+    G1 X60 Y20 F4000
+
+    G28 Z
+    G1 Z25 
+
+
+
+[z_tilt]
+z_positions:
+#   A list of X, Y coordinates (one per line; subsequent lines
+#   indented) describing the location of each bed "pivot point". The
+#   "pivot point" is the point where the bed attaches to the given Z
+#   stepper. It is described using nozzle coordinates (the X, Y position
+#   of the nozzle if it could move directly above the point). The
+#   first entry corresponds to stepper_z, the second to stepper_z1,
+#   the third to stepper_z2, etc. This parameter must be provided.
+  60,130
+  -45,10
+  165,10
+
+points:
+#   A list of X, Y coordinates (one per line; subsequent lines
+#   indented) that should be probed during a Z_TILT_ADJUST command.
+#   Specify coordinates of the nozzle and be sure the probe is above
+#   the bed at the given nozzle coordinates. This parameter must be
+#   provided.
+  85,110
+  30,5
+  120,5
+
+speed: 50
+#   The speed (in mm/s) of non-probing moves during the calibration.
+#   The default is 50.
+horizontal_move_z: 15
+#   The height (in mm) that the head should be commanded to move to
+#   just prior to starting a probe operation. The default is 5.
+retries: 5
+#   Number of times to retry if the probed points aren't within
+#   tolerance.
+retry_tolerance: 0.005
+#   If retries are enabled then retry if largest and smallest probed
+#   points differ more than retry_tolerance. Note the smallest unit of
+#   change here would be a single step. However if you are probing
+#   more points than steppers then you will likely have a fixed
+#   minimum value for the range of probed points which you can learn
+#   by observing command output.
+
+
+[bed_mesh]
+speed: 100
+horizontal_move_z: 14
+mesh_min: 10, 0
+mesh_max: 95, 80
+probe_count: 4, 4
+